Truly headless

After postponing it a number of times, I cut off the strat headstock of my very fine Warmoth neck. That took a bit of self persuation, but I needed it headless. A brass angle bracket is holding the strings. I also made a new acrylic body. This time, I tried to make it really fit my torso. I tried too hard: Most of the curves and shapes are too pronounced and it's actually too tight on the body.

Bridge and tuners are the same as in last post. I plan to make an improved version of the tuner bracket (or perhaps abandon it in favour of one using my plunger type tuners).

The pickup is a P90 mounted above the strings. I plan on experimenting with a couple of experimental pickups using primary coils with few windings and a current transformer, but I haven't gotten around to that.

It still needs a strap to be really comfortable.

Things I might do next:

• Make a steam bent plywood body in the style of the acrylic ones.
• Make a new and more ergonomic acrylic body.
  
• Make a proper wooden body for the neck and ditch the rectangular steel tube for a while.
• Test and develop my pickups.
• Get back and properly finish the two-string bass. This involves adding a slidable pickup and a piezo-pickup with preamp.

To-do list

Nothing much has happened on my T-beam-bass lately. I've replaced the jack connector since the old one didn't work and clamped the connecting cable going from the jack more securely to the sliding bracket. Plus, I've borrowed a friend's bass to do some comparisons of sound, feel and ergonomics.

His is a 34" bass, and though the picture doesn't really show it, mine, with its 30" scale length, is much smaller and lighter.

My bass still isn't exactly pretty, but I do intend it to be so one day. But until now (and probably some time ahead as well), most of my focus is on experimentation rather than looks.

Nevertheless, in an attempt to convey an idea of what I expect it to become some day, here's a list of some of the things, I'd like to do next:

• Make the saddles lengthwise adjustable for intonation, i.e. making slots for the saddles and fastening them with nuts.
• Shape the neck as shown on the image . I have to modify the sole plate of my jigsaw to be able to do that.
• Make a prettier and more ergonomic shield in 5 mm acrylic (that's approximately 0.2"). The current one is just 3 mm thick, and it's too fragile and flimsy looking.
  
• Make mahogany sides rather than the current spruce ones. What's keeping me back here is that I'm not quite sure yet where the holes for the shield are going to be, and I'd rather keep the mahogany intact and experiment on the spruce.
• Decide whether I like the sound of the vertical pickup. If so, I'll tidy up the bracket. If not, I'll buy a P-bass-pickup and use one half of that in a new bracket.

A slightly prettier sliding bracket

I've made a sliding bracket for the small pickup. It slides with little effort and easily picks up the different antinodes of the strings. Unfortunately, the pickup itself doesn't sound that good, so one of the next steps might be mounting one half of a P-bass pickup in a similar bracket - or perhaps have two sliding brackets and the usual switching arrangement.

Trying a good, well-known pickup should give me an idea of what the instrument sounds like and make it easier to find out its particular characteristics.

The system of cable and female jack on the body also works fine. I plan to add tone and volume pots down by the jack at some point.

A body that preserves vibration

With the addition of a body to the T-beam bass, it begins to resemble an instrument.

The body is a 3 mm (around 1/8") acrylic (or plexiglass) shield, cut with a saw and an angle grinder, polished, and bent in shape with a hot air gun. As with almost everything else on the bass, it is not intended as the final version. For this, I will use thicker (probably 5 mm) acrylic sheet and have the leg rest further to the back.

The acrylic shield is slightly bowl-shaped so it follows the contours of my body. It's a fairly deep bowl shape ;-) It has a leg rest bent into the lower part and an arm rest created by folding back a wing on the upper part. It quite looks like the body of an Ovation Breadwinner, though that was not the intention originally. It's very comfortable, and I expect it to be even more so when I've moved back the leg rest.

The four mounting supports that connect the shield to the stick will have to be replaced with a central support mounted on one of the two places where the stick has least vibration. A so-called node. I located the node by suspending the stick on two springy foam blocks, pouring salt on the stick and tapping it with a knife handle. As predicted in the marimba literature, the salt would gather to show the location of the node. Luckily, the node is somewhere in between the mounting supports, which makes construction easy. BTW; marimba and vibraphone builders do a lot of interesting research into the acoustics and vibration of wood; something that the guitar builders might draw upon in their work.

The reason for having the shield mounts on the node is to preserve vibration in the stick and not have it travel through the body and into the all-absorbing torso of the player. The node does not vibrate - or at least it vibrates less than other areas of the stick, meaning that less vibrations will be transferred from this point to the shield than from any other areas. I expect it to have a pronounced effect on sustain, and perhaps also on tone.

Some sort of leaf spring suspension mount might give even better isolation between the shield and the stick, but that will have to wait for a later version.